机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 路宝车后视镜盖双型腔注塑模设计

路宝车后视镜盖双型腔注塑模设计

本文ID:LW10367 字数:20889.页数:46

下载地址 全文下载链接(充值:128元) 如何充值?

路宝车后视镜盖双型腔注塑模设计

论文编号:JX659  论文字数:20889.页数:46 附外文翻译,CAD图纸

路宝车后视镜盖双型腔注塑模设计.png

摘 要
 
 塑料是一种新型工程材料,发展速度迅猛,塑料的加工和成型工艺也越来越得到重视,其中注射成型是最常用的塑料零件成型方法。
 从"后视镜盖"二板式注塑模的结构设计、制造工艺着手,对二板式注塑模的典型结构进行了剖析,对模具制造的结构工艺性(制造的可行性、经济性)进行了分析。着重介绍了二板式注塑模的结构特点和设计要点,同时,从模具制造的结构工艺方面,介绍了凸、凹模的定位加工、定模底板和剥料板的合件加工、凸模部位顶出杆孔的制造加工,以及其他的一些部位制造加工等制造要点。
 通过分析两制件的使用要求和结构特点,介绍了一模成型两个相同制件的模具结构特点及模具的动作原理,研究和分析了模具结构采用斜导柱侧抽芯和斜顶相结合,进行内、外侧抽芯成型方案的合理性,给出了模具设计的详细计算过程,实现了一模成型两个相同制件的设想,得出了此模具既方便加工又节约了材料的结论。

关键词:两板式注塑模;动模;定模;抽芯机构


Abstract

 Plastic is one kind of new engineerig material. With its rapid development, plastic processing and molding technology have been getting more and more important, and plastics injection molding is the most commom way for polymer processing.
 From "mirrors covered" two plate injection mold the structural design, manufacturing process proceed the fabrication technology begin, has carried on the analysis to the sampan type note mold's modular design, to die making's structure technology capability(manufacture feasibility, efficiency) has carried on the analysis. Introduced emphatically the sampan type note mold's unique feature and the design main point, simultaneously, from die making's structure craft aspect, introduced raised, the lower die localization processing, decides the stool and the exhausted yard lumber gathers a processing, the plunger spot to go against the pole hole the manufacture processing, as well as manufacture main points and so on other spot manufacture processing.
 Based on the analysis of the application requirement and the structural features of two plastic parts,mould structure feature and die movement theory was introduced for mould with two same parts forming at one time.Feasibility of angle-pin moving side-core slide with angled-lift for inner outer side-core slides was studied and analyzed.The design process of mold was presented in detail.Idea of manufacturing two same parts in one mould was achieved.It is concluded that the mould is easy to manufact.
Key words: 2-plate injection mold; moving die; slide; fixed die; side-core pulling mechanism

目 录

摘要………………………………………………………………………Ⅰ
Abstract…………………………………………………………………Ⅱ

第1章 绪论………………………………………………………………1
 1.1 选题的依据和意义……………………………………………… 1
 1.2 注塑模在国内外的研究现状…………………………………… 1
 1.3 存在问题和主要差距…………………………………………… 2
 1.4 毕业设计内容概述……………………………………………… 2
第2章 塑料制品总体分析………………………………………………3
  2.1 塑件结构分析…………………………………………………… 3
 2.1.1 形状特征…………………………………………………… 3
 2.1.2 脱模斜度…………………………………………………… 3
 2.1.3 壁厚………………………………………………………… 4
 2.1.4 加强筋……………………………………………………… 4
 2.1.5 圆角………………………………………………………… 4
  2.2 塑件材料特性…………………………………………………… 4
 2.2.1 塑件所用材料……………………………………………… 4
 2.2.2 ABS塑料特性……………………………………………… 4
 2.2.3 ABS塑料力学、电气性能………………………………… 5
 2.3 ABS塑料成型条件……………………………………………… 5
 2.4 型腔数的确定…………………………………………………… 5
 2.5 注射机的选用…………………………………………………… 6
   2.5.1 注射机型号的确定………………………………………… 6
   2.5.2 注射机部分参数的校核…………………………………… 6
第3章 模具总体结构设计……………………………………………  8
  3.1 分型面的选择…………………………………………………… 8
 3.2 带有活动镶块及侧向抽芯机构的选择………………………… 8
 3.3 凸凹模机构选择………………………………………………… 9
第4章 模具具体结构设计……………………………………………  10
 4.1 成型零件的设计………………………………………………… 10
    4.1.1 凹模具体结构设计………………………………………… 10
   4.1.2 凸模具体结构设计………………………………………… 12
   4.1.3 成型零件工作尺寸计算…………………………………… 13
    4.1.4 成型零件材料的选择及粗糙度要求……………………… 26
 4.2 浇注系统的选择………………………………………………… 27
 4.2.1 主流道设计………………………………………………… 27
 4.2.2 分流道的设计……………………………………………… 29
 4.2.3 浇口的设计………………………………………………… 39
 4.2.4 冷料穴的设计……………………………………………… 30
 4.3 排溢引气系统设计……………………………………………… 31
   4.3.1 排溢系统设计……………………………………………… 31
   4.3.2 引气系统设计……………………………………………… 32 
 4.4 冷却系统的设计………………………………………………… 32
    4.4.1 冷却装置的基本结构形式………………………………… 32
   4.4.2 冷却装置的设计分析……………………………………… 32
    4.4.3 冷却系统的零部件………………………………………… 35
 4.5 脱模机构设计…………………………………………………… 36
 4.5.1 顶杆脱模机构的设计……………………………………… 36
 4.5.2 成型活动镶块顶出脱模机构的设计……………………… 39
 4.5.3拉料杆的设计………………………………………………  39
 4.5.4复位系统的设计……………………………………………  40
 4.6 标准模架的选择………………………………………………… 41
 4.6.1 基本模架选择……………………………………………… 41
 4.6.2 导柱及导套的设计设计…………………………………… 41
 4.6.3 限位钉设计………………………………………………… 42
结论……………………………………………………………………… 44
参考文献………………………………………………………………… 45
致谢……………………………………………………………………… 46


路宝车后视镜盖双型腔注塑模设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:连接板落料冲孔级进模设计及CAM 下一篇:立叉切头冲孔模设计
推荐论文 本专业最新论文

点击查看关于 路宝车 后视镜 双型腔 注塑模 设计 的相关论文题目 2010-09-25 09:36:23【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有