机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 基于UG的锥差式减速器设计

基于UG的锥差式减速器设计

本文ID:LW15364 字数:15071.页数:41

下载地址 全文下载链接(充值:168元) 如何充值?

基于UG的锥差式减速器设计

论文编号:JX732  论文字数:15071.页数:41   附CAD图,UG造型三维图,装配动画

基于UG的锥差式减速器设计.png基于UG的锥差式减速器设计装配图.png

摘     要
        本文主要对一种适用于低转速,大转距,高效率及多速输出的锥差齿式减速器设计造型与仿真,整机在配流技术、减速原理、输出机构及总体结构上具有新的特点和独创,结构简单、体积小、减速比大、矩功比高、能耗低,适用于一切有供油设备的低转速、大转矩及多速输出领域,如工程机械、船用机械、大转矩机床、大功率绞车及电厂排渣设备等。其中液压驱动的运转频率一般为1000—2000/min,锥差机构的减速比通常为20—100,最大可达150。文中首先介绍了UG软件,然后重点对锥差式减速器的零件进行了造型、装配、生成爆炸图、工程图、及装配动画演示,对将来开发出锥差式液压马达做出坚实的基础。
 
关键词:锥差式  造型  装配   

The design of Offset Planetary Drive of Bevel Gear by UG


Abstract
    In this paper, the application of a low-speed, large torque, high efficiency and output of the new multi-speed gear reducer Cone poor design modeling and simulation.Whole Distribution Technology, deceleration principles, institutions and overall output structure with features and original, simple structure, volume, reduction ratio, Moment gong effective, low energy consumption, applied to all oil supply facilities and low speed, multi-speed torque and output areas, such as mechanical engineering, marine machinery, big torque machine tools, high-power winch Deslagging plant and equipment. Hydraulic drive with the running of the 1000 general -2000/min. Cone worse than the slowdown is usually 20 -100, the largest is 150. In this paper,  introduce UG software at first, and then focus on assembling the differential parts of the modeling, to generate an explosion diagram, engineering drawings, and assembly animations, then it will be to make a solid foundation on the future development of a offset planetary drive of bevel gear motor.

Keywords: awl difference -like;Modeling;assembly;
                  

目  录
中文摘要 i
英文摘要 ii
目录 iii
第一章    绪论 1
1.1概述 1
1.2 国内外现状 1
1.3 设计意义 3
1.4 本章小结 3
第二章  UG技术 4
2.1 产品开发技术和发展方向 4
2.2 UG软件中针对开发产品的模块 6
2.3 UG发展史 9
2.4本章小结 11
第三章  锥差式减速器的造型设计 12
3.1 设计装配体成品效果图 12
3.2装配功能的概述 12
3.3装配的一般思路 13
3.4 锥差式减速器的装配过程 13
3.5 锥差式减速器装配图的爆炸过程 18
3.6 锥差式减速器装配图动画 19
3.7 锥差式减速器装配体生成工程图 21
3.8 本章小结 24
第四章  锥齿轮的作用力分析和校核 25
4.1 转动锥齿轮的受力分析 25
4.2 偏摆锥齿轮的受力分析 25
4.3 偏摆锥齿轮的强度校核 27
4.4 本章小结 28
第五章  轴的尺寸确定 29
5.1 减速器低速轴的设计 29
5.2 各轴直径的确定 29
5.3 各轴长度的确定 30
5.4 轴上的倒角和退刀槽 30
5.5 本章小结 30
第六章  轴承的校核 31
6.1 32905圆锥滚子轴承的校核 31
6.2 32005圆锥滚子轴承的校核 32
6.3 本章小结 34
总结 35
参考文献 36
致谢 37


基于UG的锥差式减速器设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:基于触摸屏技术的印刷张力制控制.. 下一篇:环式摩擦系数测试装置设计
推荐论文 本专业最新论文

点击查看关于 基于 减速器 设计 的相关论文题目 2011-03-26 14:02:07【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有