机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 助力器阀盖半自动装配机设计

助力器阀盖半自动装配机设计

本文ID:LW15465 字数:10726.页数:29

下载地址 全文下载链接(充值:168元) 如何充值?

助力器阀盖半自动装配机设计

论文编号:JX768  论文字数:10726.页数:29   附CAD图

助力器阀盖半自动装配机设计文件截图.png助力器阀盖半自动装配机装配图.png

摘   要
 汽车离合器是汽车的主要部件之一,离合器助力器的设计使用目的是减小离合器踏板力,减轻驾驶员的劳动强度,增加操控灵敏度,确保行车安全。然而目前离合器助力器采用人工装配,工人劳动强度大,效率不高, 装配质量不稳定。针对这一问题,从而提出了设计一台助力器阀盖半自动装配机,来解决企业在装配方面的迫切需要。
 在设计中我首先运用SolidWorks软件完成了待装配零件的三维造型,其次根据零件特征分析确定定位方案,接下来运用SolidWorks软件计出该设备的各个部件以及完成它们的三维建模,并在三维软件里经行模拟装配,然后检查各个零件的干涉情况,如有干涉,就按实际所需的要求对部分零件经行适当的尺寸修改,最后导出装配图和部分零件的二维图。

关键词:助力器  设计   装配设备

The designing of the Booster valve cover semi-automatic assembly machine
Abstract
 The clutch is one of the main parts of the vehicle chassis. Clutch booster's design aims to reduce the clutch pedal force, to reduce the driver's labor intensity and increase the sensitivity control to ensure road safety. But,At present, the clutch booster is manual assembled, labor intensive, inefficient and the quality is inconsistent.For this issue,  the task of designing an facility of the valve seat cover of clutch booster was putted forward to satisfied the company’s urgent need for assembly .
 During the designing,I would first used Solidworks software to complete the assembly of parts to be three-dimensional modeling, second advanced the design scheme which was followed the assamby requirement, then designed the various parts of the equipment and complete their three-dimensional modeling.Using the software, it can simulate the assembly process and check the interference of each part on one another. If there is such an interference, there will be an appropriate change made on the actual part. Finally exported assembly drawings and the two-dimensional map of some of the parts .
 
Key words: Booster   design  assembly facilities  


目录
摘   要 i
Abstract ii
目录 iii
第一章   绪论 1
1.1  助力器阀座盖半自动装配机设计背景 1
1.2  设计内容概述 1
第二章  离合器助力器与自动装配简介 2
2.1离合器与助力器简介 2
2.2 装配知识简介 3
第三章  助力器阀座盖半自动装配机设计 5
3.1 零件的结构特点分析 5
3.2 整机设计 11
第四章 部分零部件的设计 18
4.1拧紧装置动力气缸的选择 18
4.2回复弹簧的设计计算 19
4.3 法兰盘的设计 20
4.4轴套的设计 21
第五章   总结 23
参考文献: 24
致 谢 25


助力器阀盖半自动装配机设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:车床进给箱体铸造工艺设计 下一篇:表面处理工程用行车结构及控制系..
推荐论文 本专业最新论文

点击查看关于 助力 半自动 装配 设计 的相关论文题目 2011-03-26 17:12:10【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有