机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 全轮驱动车辆底盘测功机结构设计

全轮驱动车辆底盘测功机结构设计

本文ID:LW15595 字数:16956.页数:34

下载地址 全文下载链接(充值:168元) 如何充值?

全轮驱动车辆底盘测功机结构设计

论文编号:JX798  论文字数:16956.页数:34   附CAD图

全轮驱动车辆底盘测功机结构设计文件截图.png

 

摘  要
 汽车底盘测功机是一项重要的室内台架检测设备,通过底盘测功机不仅可以对汽车进行动力性检测,而且还可以测量多工况排放指标及油耗,同时还能方便地进行汽车加载调试和诊断汽车在负载条件下出现的故障等。所有测试结果的准确性和可靠性都取决于底盘测功机能否对汽车的道路行驶阻力做出真实的模拟。
  本文从底盘测功机的几个基本装置概述开始,结合其发展现状,对其工作原理、机械结构以及测试过程中的道路行驶阻力进行分析,完成了本次设计。在设计中主要对驱动电机、转鼓、传感器以及风冷装置等进行了型号和尺寸的选定,并确定了安装尺寸,完成了结构设计图。
 本文提出了利用交流测功机来取代传统的电涡流测功机和水力测功机,通过先进的变频调速技术来控制交流测功机以再现汽车的道路行驶情况。不仅省去繁琐的惯性飞轮,简化了机械结构,而且可以实现惯量的无级模拟。


关键词:底盘测功机  动力性  道路行驶阻力  交流测功机

The Structural Design Of All-wheel Drive Vehicle Chassis Dynamometer

Abstract
 The Chassis Dynamometer is an important indoor bench testing equipment, through the chassis dynamometer,it can not only have a testing for the power of the car, but also can measure the status of multi-emissions and fuel consumption indicators, at the same time it   can easily debug and diagnosis of motor vehicles loaded car under load fault conditions, such as. All test results are determined by the accuracy and reliability of the chassis dynamometer can of road vehicles to make a real simulation of the resistance.
 This article from the chassis dynamometer to start an overview of several basic devices, combined with its development of its working principle and analysis of mechanical structure, completed the design. Mainly in the design of the drive motor, drum, air-cooled devices, such as sensors, as well as a selection of models and sizes and to determine the size of the installation to complete the structural design.
 In this paper, the use of the exchange of dynamometers to replace the traditional eddy current dynamometer and hydraulic dynamometer, through advanced technology for the control of  AC dynamometer to reproduce the situation of road vehicles. Not only the inertia of the flywheel eliminate red tape and simplify the mechanica structure, and can be achieved without the level of inertia simulation.

Keywords: Chassis dynamometer  Dynamic  Road Resistance   AC Dynamometer

目  录
中文摘要 I
英文摘要 II
目  录 III
第一章 绪论 1
1.1 汽车底盘测功机概述 1
1.1.1加载装置 3
1.1.2测量装置 3
1.1.3转鼓 4
1.1.4其它装置 4
1.2 底盘测功机的发展现状 4
1.3 汽车底盘测功机的工作原理 5
1.4  汽车底盘测功机的测控系统 8
1.4.1汽车底盘测功机测控系统开发的意义 8
1.4.2汽车动力性评价指标 8
1.4.3汽车动力性评价指标体系 9
第二章  汽车底盘测功机的结构 11
2.1 底盘测功机硬件系统 11
2.2 机械结构 11
2.3底盘测功机的结构设计 12
2.3.1驱动电机 13
2.4 辅助装置设计 21
2.5汽车底盘测功机的加载装置的选型 22
第三章 底盘测功机功能介绍 26
3.1测功 26
3.2 测速 26
3.3 制动 26
3.4反拖 27
第四章 结论 28
参考文献 29
致  谢 30


全轮驱动车辆底盘测功机结构设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:汽车密封条制造工艺 下一篇:轻型货车膜片弹簧离合器设计
推荐论文 本专业最新论文

点击查看关于 全轮 驱动 车辆 底盘 测功机 结构设计 的相关论文题目 2011-03-27 09:39:44【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有