机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 棒材超声检测自适应机械平台设计

棒材超声检测自适应机械平台设计

本文ID:LW18356 字数:15261.页数:32

下载地址 全文下载链接(充值:158元) 如何充值?

棒材超声检测自适应机械平台设计

论文编号:JX955  论文字数:15261.页数:32   附CAD图

棒材超声检测自适应机械平台设计所有文件.png棒材超声检测自适应机械平台设计总装图.png

 摘     要
 本文提出了棒材超声检测自适应机械平台的设计,该平台主要可以实现棒材在垂直方向的举升,以使得棒材进入三爪机构。平台设计的举升行程为120mm,最大举升力为1000Kg,适用的棒材直径φ28~φ200mm,适用棒材长度0.5~5m。该设计分成两个部分:一个是棒材超声检测平台机械结构的设计,另外一个是平台气动系统的设计。第二章和第三章主要介绍了机械结构部分的设计及其理论分析计算和强度校核;第四章进行了平台主气缸气动方案的设计和各个气动元件功能说明;第五章对气缸的控制方式进行了分析和研究。
 
 
 关键词:棒材  超声检测  自适应  平台
The Design of Ultrasonic Detection Adaptive Platform of Metal Robs
Abstract
 This paper introduces the design of ultrasonic detection adaptive platform of metal robs, the platform mainly achieves robs vertical lifting, in order to enable Robs enter three-jaw agency. The lifting travel of platform is 120mm,the maximum lifting capacity is 1T,the application of the robs diameter isφ28 ~φ200mm,the application of the robs length is 0.5 ~ 5m.The design is divided into two parts.One is the mechanical structure of ultrasonic detection adaptive platform of metal robs.The other is the design of platform pneumatic system.Chapters II and III introduce the main part of the mechanical structure design and its theoretical analysis and strength check calculation. Chapters IV introduces the design of pneumatic system and pneumatic components of the function of each note.Chapter V analyzes and studies the control of the pneumatic cylinder.
 
 Keywords: Rob;  Ultrasonic detection;  Adaptive;  Platform

 目 录
 Abstract ii
 第一章 绪论 1
1.1 研究背景及意义 1
1.2 国内外研究状况 1
1.2.1 国内研究现状 1
1.2.2 国外研究现状 2
1.3 技术要求 4
 第二章 机械平台结构设计 5
2.1 总体初案设计 5
2.2 举升机构的设计 5
2.3 棒材支撑机构的设计 6
2.4 夹紧机构的设计 7
2.5 转臂的联接设计 7
 第三章 校核计算 9
3.1 转臂的受力分析 9
3.2 主动转轴的校核计算 11
3.3 键与销轴的校核计算 11
 第四章 气动方案设计 13
4.1 气动系统的工作要求 13
4.2 气动回路的设计 13
4.3 主气缸尺寸的计算和选择 16
4.4 控制元件的功能及选择 18
4.5 气动三联件和压缩机的选择 19
 第五章 自适应控制 21
5.1 气缸控制方式 21
5.2 分段PID控制 22
5.3 迭代控制 24
 第六章 总结 26
 参考文献 27
 致  谢 28


棒材超声检测自适应机械平台设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:大众途安车型电器开关的开发 下一篇:Ф12mm绕线收线机的设计
推荐论文 本专业最新论文

点击查看关于 棒材 超声 检测 适应 机械 平台 设计 的相关论文题目 2011-04-10 17:22:50【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有