机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 新型电吹风三维造型设计及快速成型制作

新型电吹风三维造型设计及快速成型制作

本文ID:LW18370 字数:16296.页数:77

下载地址 全文下载链接(充值:168元) 如何充值?

新型电吹风三维造型设计及快速成型制作

论文编号:JX969  论文字数:16296.页数:77  附CAD图,三维图

新型电吹风三维造型设计及快速成型制作缩略可视图.png

摘     要
 本文主要论述新型电吹风三维造型设计及快速成型制作,主要阐述了新型电吹风的详细设计步骤、模型制作及后处理过程。在造型设计过程中使用的主要操作有拉伸、旋转、阵列、曲面合并、抽壳、拔模等等的命令,而这些命令可以在右边工具栏中或者上面的菜单栏里直接找到;在模型制作时,工作人不能离开工作中的快速成型机,否则纸容易走偏从而使零件报废;在进行模型后处理时,我们主要用的工具是502胶水和砂纸,对模型进行上胶和打磨,打磨过程中要特别注意模型细小部位,这些地方容易破损,一旦发现有破损则应立即用502胶水补上。
 在本次毕业设其中使用的三维软件是PROE,快速成型设备为HRP-ⅡB快速成型机,对于我设计的新型电吹风有市场上没有的特点,其结构简单、美观、实用,而且在使用HRP-ⅡB快速成型机完成模型制造后容易剥离等后处理工作。

关键词:新产品  电吹风  三维造型  快速成型   后处理


3D design for a new hair dryer and rapid prototyping

Abstract
 This paper is showing about the 3D modeling for a new hair dryer and rapid prototyping, mainly describing the detailed design steps of the new hair dryer, modeling and post processing . The main operations used in 3D modeling is extrude, rotation, array, surface merge, pumping shell, drfting and so on. These commands could be directly found in the right toolbar or the menu bar; While the rapid prototyping machine is making the model we can’t going anywhere ,or the paper would get the wrong way then the model is crapped; During post-processing model, our main tool is the 502 glue and sand paper, glueing on the model and grinding, grinding process, special attention should be pay to the small areas of the model where could be easily damaged, if damaged areas founded,it shall be immediately fixed by using 502 glue.
 The 3D software PROE is used in this graduate design, rapid prototyping equipment is named HRP-Ⅱ B rapid prototyping machine, my new hair dryer have its special structure,which did not have in the market, and it is simple、beautiful and practical. And it is easy for post-processing such as peeling out the model after the model was completely made by the HRP-Ⅱ B model manufacturing rapid prototyping machine.


Keywords:  New Products  Hair dryer  3D modeling  Rapid Prototyping  Post-processing 

目  录
摘     要 I
Abstract II
第一章:绪论 1
1.1 选题的背景与意义 1
1.1.1、研究的基本内容与拟解决的主要问题 2
1.1.2、电吹风各部分的作用 2
1.1.3、研究的方法与技术路线 3
1.2  新型电吹风的设计思路 3
第二章:产品的初步设计思路 5
1.1、新产品大致开发过程 5
1.2、确定产品大致外形尺寸 6
第三章:新型电吹风造型过程 7
3.1 电吹风左半 7
3.2 电吹风右半 24
3.3 电吹风端盖 31
3.4 电吹风壁挂及操作板 35
3.5 聚风口 41
3.6 最终装配 44
第四章:新型电吹风快速成型制作 45
4.1 关于快速成型 45
4.2 新型电吹风快速成型 50
4.2.1  对零件文件进行另存格式 50
4.2.2  使用HRP-II B快速成型机进行模型制作 52
4.3  模型的后处理 54
4.3.1  模型的剥离 54
4.3.2  模型的上胶,打磨完成后处理 56
第五章:毕业设计小结 58
参考文献 59
致  谢 60
附 录 61


新型电吹风三维造型设计及快速成型制作......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:直流直线电机驱动式自动窗帘设计 下一篇:铃盖的注塑模设计
推荐论文 本专业最新论文

点击查看关于 新型 电吹风 三维 造型设计 快速成型 制作 的相关论文题目 2011-04-10 18:27:38【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有