机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 三杆并联机床控制系统设计

三杆并联机床控制系统设计

本文ID:LW19596 字数:21100.页数:72

下载地址 全文下载链接(充值:158元) 如何充值?

三杆并联机床控制系统设计

论文编号:JX1457  论文字数:21100.页数:72   附CAD图

三杆并联机床控制系统设计文件截图.png三杆并联机床控制系统设计装配图.png三杆并联机床控制系统设计电气原理图.png

摘  要

 并联机床使将近两个世纪以来以笛卡尔坐标直线位移为基础的机床结构和运动学原理发生了根本性的变革,抛弃了固定导轨的刀具导向方式,采用了多杆并联机构驱动 ,完全打破了传统机床结构的概念。
 对并联机床进行机电一体化设计,要求有机床的机械结构设计,有机床控制部分的设计及部分参数的测量仿真。本次设计首先进行了并联机床的总体设计,分为伺服系统选择;控制系统选择;传动系统选择三个方面。其次是机械传动设计主要对机床的各个硬件部分计算,选型,校核。然后是步进电机驱动硬件设计,介绍了PLC,选择了步进电机的驱动电路,对传感器进行了选择,PLC端口的设计。最后是LabVIEW仿真,介绍了LabVIEW,并对所选传感器所测的参数进行仿真。
关键词:并联机床, PLC控制, 步进电机驱动, LabVIEW仿真

Abstract
 
 Parallel machine tool has undergone a fundamental change linear displacement of the structure and kinematics of machine tools based on Cartesian coordinates, so that nearly two centuries, abandoned the fixed guide way of the tool-oriented, using a multi-bar parallel mechanism driven, completely broke the traditional notion of the machine structure. This design first for the overall design of the parallel machine.
 About mechanical and electrical integration of the PMT Design, requires the mechanical structure design of machine tools, the design of A machine tool control part and some of the parameters in simulation, Divided into three ways the servo system selection, control system selection and drive selection. Followed by the mechanical transmission system is mainly on the machine calculation , selection and check of the various hardware components. Then is the stepper motor drive hardware design, Introduced PLC, Select a stepper motor drive circuit, choose the sensor, design the PLC port. Finally, Simulate LabVIEW, Introduced LabVIEW. And simulate the selected parameters measured by sensor.
Keywards: PMT, PLC control, Stepping Motor Driver, LabVIEW Simulation

 

目    录

第一章 绪论 1
第1.1节  什么是并联机床 1
第1.2节  并联机床的发展 1
第1.3节  国内并联机床研究现状 4
第1.4节  并联运动机床的发展展望 6
第1.5节  毕业设计目的与要求 6
第二章  并联机床控制系统总体方案的确定 8
第2.1节  伺服系统的选择 8
第2.2节  控制系统选择 8
第2.3节  传动系统选择 8
第三章  机械传动设计 10
第3.1节  确定系统脉冲当量 10
第3.2节  滚珠丝杠计算、选择 10
第3.3节  谐波减速器的选择 16
第3.4节  步进电机惯性负载的计算 19
第3.5节  步进电机的选用 19
第四章 步进电机驱动硬件设计设计 22
第4.1节   PLC概述 22
第4.2节  步进电机驱动电路设计 26
第4.3节  转速传感器 33
第4.4节  拉力传感器 37
第4.5节  PLC端口设计 39
第五章 LabVIEW仿真 41
第5.1节  LabVIEW简介 41
第5.2节  主要特点 41
第5.3节  LabVIEW仿真设计 42
第六章  总结 44
参考文献 45
英文原文 47
中文译文 59
致  谢 69


三杆并联机床控制系统设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:液压缸装配生产线上的机械上帽机 下一篇:斜井提升机的箕斗设计
推荐论文 本专业最新论文

点击查看关于 机床 控制系统 设计 的相关论文题目 2011-05-07 21:35:19【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有