机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 打火机金属外壳的冷冲压模具设计

打火机金属外壳的冷冲压模具设计

本文ID:LW20189 字数:16567.页数:32

下载地址 全文下载链接(充值:168元) 如何充值?

打火机金属外壳的冷冲压模具设计

论文编号:JX1495  论文字数:16567.页数:32 附任务书,开题报告,实习报告,外文翻译,CAD图

打火机金属外壳的冷冲压模具设计文件截图.png打火机金属外壳的冷冲压模具设计装配图.png

 摘要
 本次课题打火机金属外壳的冷冲压模具设计,通过这次设计,进一步熟悉冲压模具的设计流程运用落料、冲孔、弯曲等冲压工序设计冷冲压成形模具,需要解决很多的关键问题,对零件进行工艺分析,进行冲压工艺方案及模具结构方案设计和对冲压模具零部件工艺参数进行参数选择及验算,绘制冲压模具装配图和零件图。需要运用机械、材料成形、冷冲压模具、计算机二、三维设计等多学科的知识,需要相当广阔的知识面和较高的专业水平。通过对零件进行工艺分析和工艺参数计算,根据零件所需冷冲压工序设计出连续冲压模具,同时运用AutoCAD绘制二维模具装配图和零件图还得同时对部分零件进行了加工工艺分析。该零件复杂且尺寸不规则,这对模具设计和展开排样提出了较高的要求,特别是弯曲过程,需要合理的安排工艺,巧妙的设计冲模来解决,对于部分不关键的零件可适当降低尺寸公差要求,设计中尽可能使用标准件,有利于设计成本的降低。
 关键词:冷冲压模具,工艺分析,连续模,打火机金属外壳
 
  
 Abstract
 This topic lighter metal exterior cold stamping mould design, through the design, further stamping mould design process using blanking, punching, bending stamping process design of cold stamping mould, needs to solve the key problems of many parts, technical analysis, stamping process scheme and the die structure and design of stamping mould parts process parameters parameter selection and calculation, stamping, assembly and detail drawings. Need to use machines, materials, stamping, molding, cold, 3d design of computer science knowledge, need quite a broad knowledge and professional level. Through the analysis of the technology of parts and the process parameters calculation, cold stamping parts needed to process a compound stamping mould design, and using AutoCAD assembly drawing two-dimensional mould parts and also have also made for parts processing analysis. The components and complex, the size of irregular of mold design and layout puts forward higher requirements, especially the bending process, need reasonable arrangement of the clever design process, stamping parts, to solve the key parts for not properly reduce dimension tolerance requirement,design as far as possible, to use standard design cost reduction.
 keywords: Cold stamping mould,Process analysis,Continuous mode,Lighter metal shell

目录
1 引言 5
2 工艺方案确定 7
2.1  零件及冲压工艺分析 7
2.2 工艺方案确定与工艺流程图 8
2.2.1工艺方案确定 8
2.2.2工艺流程确定 8
3 工艺参数的计算 10
3.1 毛坯的尺寸计算 11
3.2 冲裁排样及材料利用率的计算 11
3.3各部分工艺力的计算 12
3.3.1 冲裁压力的计算 12
4 主要工作部分尺寸计算 14
4.1 预切断凸凹模的刃口尺寸计算 15
4.2 冲孔凸凹模刃口尺寸计算 15
4.3弯曲冲孔凸凹模高度的确定 16
4.4冲孔凸模的强度和刚度校核 17
4.5凸凹模的结构选择设计 18
5 其他零件设计 18
6 压力机的选择 25
7 部分零件加工工艺过程 26
8 模具的装配和使用 28
9 经济性分析 30
10 结 论 31
参 考 文 献 32
致  谢 33


打火机金属外壳的冷冲压模具设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:游标卡尺盒注塑模具设计 下一篇:Φ39转子端盖冲压工艺及冲孔、落..
推荐论文 本专业最新论文

点击查看关于 打火机 金属 外壳 冲压 模具设计 的相关论文题目 2011-06-12 08:33:25【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有