机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 黄铜焊片冲孔落料级进模设计

黄铜焊片冲孔落料级进模设计

本文ID:LW22056 字数:11612.页数:29

下载地址 全文下载链接(充值:168元) 如何充值?

黄铜焊片冲孔落料级进模设计

论文编号:JX1540  论文字数:11612.页数:29  附任务书,开题报告,外文翻译,CAD图,答辩PPT

黄铜焊片冲孔落料级进模设计文件截图.png排料图.png工件图.png

黄铜焊片冲孔落料级进模设计

 【摘要】冷冲压模具在模具中占有相当重要的地位,产品波及范围大,约占模具总数的一半,所以受到各方面的高度重视,而冲压件的质量好坏在很大程度上取决于模具设计、制造的技术水平。
 本设计要求的制件材料为黄铜,且厚度为1mm,大批量生产,涉及落料、冲孔,所以采用级进模是非常适合的。设计的级进模采用弹性卸料、挡料、导柱、导套配合导向,通过冲孔凸模、落料凸模和凹模共同作用,完成冲制过程。在滑块的一次行程内,完成所有冲压要求,从而大大的提高了生产效率。冲压模具设计的全过程:
 1. 经工艺分析与工艺计算,确定了该设计工艺流程及冲模结构形式。
 2. 同时对所设计的模具进行了分析说明。
 3. 对压力机做出了合理的选择。
 4. 整个过程采用AutoCAD软件绘制模具的二维装配图和零件图。
 
 【关键词】冲孔 ;落料 ;模具设计 ;级进模 ;生产效率

 

Brass welding pieces punchingblankingprogressive die design
  [Abstract] Cold stamping mould in mould occupies an important position, product scope affected big, accounts for about half of the total number of mould, so by every aspect highly, and stamping quality stand or fall depends greatly on and mold design and manufacturing technology level. This design requirement of stamping materials for H62, and the thickness of 1 mm, mass production, involving blanking, punching, so using progressive die is very suitable. Design of progressive die using elastic and unloading, and block material, guide pin, guide set with guidance, through the punching the punch, blanking the punch and dies, the joint action, complete blunt system process. The slide block within the trip, complete all stamping requirements, thus greatly improve the efficiency. Stamping mould design process of:
1. The process analysis process calculation, inner-space value choice, to determine the design process and die structure.
2 at the same time the design of mold respectively were analyzed and explained.
3. To press a reasonable choice.
4. The whole process using AutoCAD software rendering mould 2d drawings and individual detail drawings.

 [Key words] Punching; Blanking; Mould design; Progressive die; Production efficiency

 

目  录

毕业设计(论文)任务书 Ⅰ
开题报告 Ⅱ
指导教师审查意见 Ⅲ
评阅老师评语 Ⅳ
答辩会议记录 Ⅴ
中文摘要 Ⅵ
外文摘要 Ⅶ
前言 1
1 选题背景 3
1.1 题目来源 3
1.2 研究目的和意义 3
1.3 国内外研究现状、发展趋势及存在的主要问题 3
2 方案论证 6
2.1 零件加工工艺分析 6
2.2 冲裁件的工艺性 6
2.2.1 排样设计 8
2.3 冲压力计算 9
2.4 计算冲压力 10
2.4.1 压力中心 11
2.5 压力机的选择 12
2.6 凸、凹模刃口尺寸的确定及公差计算 12
2.7 模具结构设计 14
2.8 冲压模具材料的选择 19
3 冲压模具的安装、调试和日常修理与保养 21
3.1 模具的安装的一般顺序: 21
3.2 冲模的试冲和调整 21
4 总结 22
参考文献 23
致 谢 24
附录 25


黄铜焊片冲孔落料级进模设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:基于SolidWorks的汽车齿轮齿条式.. 下一篇:电动螺旋拆卸器设计
推荐论文 本专业最新论文

点击查看关于 黄铜焊片,冲孔落料级进模, 的相关论文题目 2011-10-15 13:48:00【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有