机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 转筒干燥器的总体与结构设计

转筒干燥器的总体与结构设计

本文ID:LW24631 字数:11852.页数:35

下载地址 全文下载链接(充值:168元) 如何充值?

转筒干燥器的总体与结构设计

论文编号:JX1639  论文字数:11852.页数:35 附任务书,开题报告,外文翻译,CAD图

转筒干燥器的总体与结构设计.png

转筒干燥器的总体与结构设计
摘要:在化学生产中,有些原料,半成品或成品含有或多或少的水分或其他溶剂。为了满足使用的要求,常采用干燥的方法将这些水分或溶剂除去,而干燥的方法和设备是多种多样的。
 回转干燥器是一种常见的干燥设备。它适合于颗粒状,湿物料的干燥,如纯碱,硝铵,和各种盐类等。回转干燥器能使物料在滚桶内翻动,抛撒,与热空气或烟道气充分接触,干燥速度快,生产力较高,因此广泛应用于化工,食品等工业生产中。
 设计的主体部件是1000×8000mm规格的转筒部分,筒的转动依靠齿轮带动,筒的重量主要由两个托轮支撑,而托轮则由两个轴承支撑,抄板翻动物料。
 该设备生产能力大,结构简单,但是效率较低。

关键词:回转   托轮   齿轮   轴承   抄板
      

ROTARY DRYER WITH THE STRUCTURAL DESIGN OF THE OVERALL
Abstract: In the processing of the chemistry industry, some materials,semi-finished produces or finished produces  contain more or less imprecision or other solvents.In order to satisfy the requirements of use, we need rid them by drying technology. There are many kinds of  the methods equipments for drying.
 The drying machine of turning cylinder is an old equipment and are in common use .It is fit to dry the wet materials ,such as sulphur ,all kinds of salts etc .It can make the materials turning over,throwing or scattering , and contact with the hot air amply .It’s drying speed is faster, and the manufacture ability is also very good .So it applies to the processing of the chemistry ,foodstuff etc widely.
 The assignment of the design is the turning around section of serial 1000×8000mm .The turning of tube-shaped object depends on the gears .The weight is sustained with two supporting wheels .The supporting wheels is sustained with two bearing .The funtion of lifting of board is to turn over the matters.
 The manufacture ability of this equipment is larger ,and the structure is simple ,but the efficiency is very lower.
Keywords: turning around ,supporting wheels ,the gears ,bearing ,lifting board .
 目   录


1 引言 1
2 概述 2
2.1 干燥的目的 2
2.2 干燥机的选用基准 2
2.3 转筒干燥器的主要组成及作用 3
2.4 转筒干燥器的工作原理 4
2.5 转筒干燥器的特点 4
2.6 转筒干燥器的分类及适用范围 5
2.6.1 直接加热式 5
2.6.2 间接加热转筒干燥器 6
2.6.3 复式加热转筒干燥器 6
3  转筒的结构部分 8
3.1 筒 体 8
3.2 滚  圈 11
3.3 托  轮 13
3.4  抄   板 14
3.5 电机的选择 15
3.6  减速机的选择 16
3.7 联轴器的选择 18
3.8  轴的校核 19
3.9 轴承的校核 23
3.10 齿轮的校核 24
3.11  转筒的密封 30
4 转筒的安装、调整和运转 31
5 结论 32
参考文  33
致   谢 34


转筒干燥器的总体与结构设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:沟槽凸轮机构的设计和运动仿真 下一篇:管磨机的总体和结构设计
推荐论文 本专业最新论文

点击查看关于 干燥器 总体 结构设计 的相关论文题目 2012-04-15 09:19:24【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有