机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 下管衬管落料冲孔模设计

下管衬管落料冲孔模设计

本文ID:LW45722 字数:12026.页数:28

下载地址 全文下载链接(充值:168元) 如何充值?

下管衬管落料冲孔模设计

论文编号:JX1686  论文字数:12026.页数:28 附任务书,开题报告,外文翻译,答辩PPT,CAD图

下管衬管落料冲孔模设计.png

下管衬管落料冲孔模设计
 【摘要】本设计课题下管衬管落料冲孔件,材料为Q235,厚度为1.0mm,属于大批量生产,精度要求IT10。
 本文的主要内容是分析它的工艺性并设计它的冲压模具。首先根据该零件的结构特点和所用材料特点进行工艺分析和工艺计算,进而确定出工艺方案。根据确定的工艺方案,选择落料冲孔复合冲裁模;然后根据工艺计算对模具的具体结构和所需各个零件进行设计和选择,通过计算各所需力,初选用压力机为开式可倾工作台压力机J23-40,其公称压力为400KN;最后在计算机上用CAD绘图软件画出所有的总装图和零件图,并标注各个零件的尺寸,技术要求及其制造标准。设计过程中参考了各种文献资料和技术标准。
 【关键词】冲压工艺 ;复合模 ;模具设计

 Down tube liner tube blanking punching die
 
 [Abstract] this design topic down tube liner tube blanking punching parts, material for theQ235, thickness of 1.0mm, belongs to the large scale production, precision IT10. The main content of this article is to analysis its process and the design of the stamping die.According to the structural characteristics of the parts and materials for the characteristics of the process of analysis and calculation, and further determines the process scheme.Determine the process scheme, selection of blanking punching compound die; then according to the technological calculation of die structure and the specific required each part design and selection, through the calculation of the needed force, primaries with press for the inclinable bench press J23-40, its nominal pressure 400KN; finally on the computer using the CAD drawing software draw all the assembly drawing and parts drawing, and label each components size, technical requirements and manufacturing standards.The design process with reference to various literature and technical standards.
 [Key words]  Stamping process  Compound die  Mold design

目  录
毕业设计任务书 Ⅰ
开题报告 Ⅱ
中文摘要 Ⅵ
外文摘要 Ⅶ
前言 1
1 选题背景 1
1.1 题目来源 1
1.2冲压加工的特点及其应用 1
1.3冲压模具的现状及发展方向 2
1.4当前存在的问题 5
2 方案论证 5
2.1零件加工工艺分析 5
2.2工艺方案确定 6
2.3断面特征 7
2.4模具结构形式的确定 7
3  模具设计计算 8
3.1冲裁力的计算 8
3.2卸料力及推件力的计算 9
3.3冲压设备的选择 10
3.4冲裁间隙的确定 11
3.5冲模刃口尺寸的计算 12
3.6 排样 17
3.7 模具总体结构 18
3.8冲压模具材料选择 18
4模具的安装、调试 19
4.1 模具安装的一般顺序 19
4.2模具的调试 21
总结 23
参考文献 24
致谢 25


下管衬管落料冲孔模设计......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:旋钮塑料模具设计 下一篇:汽车制动蹄结构件工艺规程设计及..
推荐论文 本专业最新论文

点击查看关于 管衬管 孔模 设计 的相关论文题目 2012-09-29 21:02:31【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有