机械设计论文网


  • 首页|
  • 机械模具设计论文|
  • 机械模具开题报告|
  • 机械模具免费论文|
  • 机械模具外文翻译|
  • 数控论文|
  • 机械原创论文|
  • 焊工钳工论文|
  • 理工科论文|
         模具专业毕业设计   机械专业毕业设计   数控专业毕业设计

论文降重

当前位置:机械设计论文网 -> 机械模具毕业设计论文 -> 双电机自同步直线振动筛

双电机自同步直线振动筛

本文ID:LW6165 字数:14682,页数:65

下载地址 全文下载链接(充值:128元) 如何充值?

双电机自同步直线振动筛

论文编号:JX470   有设计图,论文字数:14682,页数:65

双电机自同步直线振动筛.png双电机自同步直线振动筛装配图.png

摘 要

选煤厂的筛分机数量很多,所以对筛分机的要求也越来越高。不但要求它具有较高的生产率、较好的筛分效率或脱水效果、较低的动力消耗;而且还要具备结构简单、制造容易、安装维修方便等机械性能。由于滚轴筛、圆筒筛上述性能较差,在使用上受到了限制,逐渐被工艺效果好、构造简单、维修方便的振动筛所代替。
自同步振动筛是一种广泛用于散体物料分级的设备。在选煤等工业领域,用于分级、脱水、脱泥和脱介。其筛分性能尤其重要。
本文系统地阐述了双电机自同步振动筛的应用现状和发展趋势,论述了设计高效双电机自同步振动筛的必要性;同时对双电机自同步振动筛的原理进行了分析,计算了振动筛的动力学参数、运动学参数,设计计算了激振器的轴、偏振块的参数和结构,进行联轴器的选型等。

关键词  双电机 自同步振动筛 激振器


Abstract

A Washery the large number of screening machine, so the demands on the screening machine also getting higher and higher. It is not only demand higher productivity, better screening efficiency or effectiveness dehydration, low power consumption, but also with simple structure, easy to manufacture, installation and maintenance convenient mechanical properties. As roller sieve, sieve cylinder of the poor, by the use of restrictions have been gradually effect of good, simple structure and easy maintenance replaced by the shaker.
In this paper, systematically expounded the two-synchronous motor shaker since the application status and trends on the design of highly efficient dual-synchronous motor shaker since the necessity of the dual-motor while simultaneously shaker since the principle of the analysis, calculate the shaker The parameters, parameters of kinematics, design and calculation of the axis of the exciter, the parameters and polarization block structure, such as coupling the selection.

Keywords  double motor  since the double-synchronous motor shaker vibrator

  
目 录
摘 要 I
Abstract II
第1章 绪论 1
1.1  课题研究的目的及意义 1
1.1.1  课题研究的目的 1
1.1.2  课题的意义 1
1.2  国内外振动筛分机械的发展 3
1.3  本次设计的内容 5
第2章 整体结构设计 6
2.1  传动方式的选择 6
2.2  设计方案介绍与选择 7
2.3  减震装置的确定 9
2.4  激振器结构设计 10
2.4.1  激振器结构类型的选择 10
2.4.2  工作原理分析 11
第3章 双电机自同步振动筛参数确定 14
3.1  自同步筛的工艺参数的确定 14
3.2  振动筛动力参数计算 17
3.2.1  惯性振动筛参振质量的计算 17
3.2.2  计算隔振弹簧刚度 18
3.2.3  所需激振力力幅及质量矩的计算 19
3.2.4  振动筛传给地基的负荷 19
3.3  电动机功率的计算与电机选择 21
第4章 激振器的设计计算 24
4.1  偏心块的设计 24
4.2  激振器传动轴的设计与计算 31
4.3  键的强度校核 35
4.4  轴承的校核 36
4.5  轴承的润滑 37
第5章 筛箱的设计分析与计算 38
5.1  筛面选择 38
5.2  筛面固定方法的确定 41
5.3  筛框的设计 43
第6章 成本和经济效益分析 44
结 论 45
致 谢 46
参考文献 47
附录1 49
附录2 55


双电机自同步直线振动筛......
论文人工降重
本论文在机械模具毕业设计论文栏目,由机械设计论文网整理,转载请注明来源 www.jixielw.top 更多论文,请点机械设计论文网查看
上一篇:S150掘进机行走机构设计 下一篇:JBT62轴流式通风机结构设计
推荐论文 本专业最新论文

点击查看关于 电机 同步 直线 振动筛 的相关论文题目 2010-03-28 23:40:46【返回顶部】
联系方式

相关栏目

数控专业论文
机械设计原创毕业论文
机械模具毕业设计论文
焊工钳工技师论文
机械模具开题报告
理工科论文下载
机械模具免费论文
机械模具外文翻译
联系方式

热门论文

联系方式


机械设计论文网提供机械设计论文范文,行政管理毕业论文,网站永久域名www.jixielw.top 

本站部分文章来自网友投稿上传,如发现侵犯了您的版权,请联系指出,本站及时确认并删除  E-mail: 17304545@qq.com

Copyright@ 2009-2021 机械设计论文网 版权所有